Skip Navigation Website Accessibility
532 N Wenatchee Ave
Wenatchee, WA 98801


We check the “set-up” on all the guitars we receive and sell. However, guitars are made of wood and wood is sensitive to temperature and humidity. Whether handing on a store display rack or sitting in a case in your home, temperature and humidity may cause changes in the guitar’s set-up. This is normal. Also, if you change the gauge of strings you use, the set-up can be affected. These are some general, basic set-up steps. If this seems complicated or you are unsure about what you need to do after reading these steps, please bring your guitar in to the store. We can answer your questions or you can have set-up done by one of our qualified guitar technicians.


All modern guitars have an adjustable metal truss rod that runs down the center of the neck. The truss rod adjustment can be both simple and complex at the same time. On the simple side, a minor adjustment to straighten a neck with too much concave bow or to relieve a convex bow is possibly all that is needed to make a dramatic improvement to your guitars playability. On the complex side, adjusting the rod alters other aspects of the set-up such as overall action, string height and intonation. NOTE: YOU CAN DAMAGE YOUR GUITAR PERMANENTLY IF THE ADJUSTMENT IS NOT MADE CORRECTLY. If you feel confident that you can make this adjustment…read on.

  • Place a capo at the first fret.
  • Press the low E string down at the 17th fret.
  • Look for a small gap of (approximately .010” or 0.25mm) between the top of the 7-9th fret and the underside of the string.
  • If there is too much gap, the truss rod needs to be turned clockwise.
  • If there is not enough gap, the truss rod needs to be turned counter clockwise.


  • Never force the adjustment if it feels tight.
  • Make any adjustment in very small degrees at a time.
  • Let the neck “settle” between adjustments.
  • If you are not clear on these instructions, bring your guitar in to the store and let us help.


Once you are sure your truss rod has been adjusted properly, you will want to adjust the action or string height to insure the best playability. String height is measured at the 12th fret.

  • Using a steel ruler, measure the action on the top and bottom strings.
  • Adjust the bottom string (low E) to 2.00mm and the top string (high E) to 1.5mm by raising or lowering the saddle.
  • Set the middle strings by gradually increasing the height from treble to bass side.


Most electric guitars provide individual string length adjustment for setting intonation. Fine tuning this length insures that your guitar plays in tune all the way up and down the neck.

  • Using an electronic tuner, tune your guitar to pitch.
  • One string at a time, play the harmonic at the 12th fret and then play the fretted 12th fret note.
  • If the fretted note is sharper than the harmonic, increase the string length slightly until both notes register the same on your tuner.
  • If the fretted note is flat compared to the harmonic shorten the string length slightly until both notes register the same on your tuner.
  • Repeat the procedure on all strings until the harmonic and the fretted notes are the same.


Pick-up height can greatly effect your guitars output. The closer to the strings the pick-up is, the more output you will get but….if the pick-up is too close the strings, problems can occur with magnetic pull.

  • Fret the outer strings (one at a time) at the top fret.
  • Measure the distance from the top of the pick-up to the underside of the string.
  • Adjust so there is between 2.5mm and 3.00mm.
  • Do not hesitate to call us or come by the store for help!

Fender Guitar and Bass Set-up Guides – Links

Here are some links to the Fender website and their official guides for setting up Fender guitars and basses.

Stratocasters      Telecasters      Bass Guitars      Other Guitars


Monday - Friday:

12pm - 6pm

12pm - 5pm

Closed Sundays and most major holidays. 



Avalon Music, Inc. 
532 North Wenatchee Ave.
Wenatchee, WA 98801
509.664.0560 (fax)